DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited. *This publication supersedes TM , 3 August FM PREFACE. This manual is intended for use by engineer commanders, staff officers, combat engi- neers, and bridge specialists who. M-2 Bailey Bridge (FM ) [Department of the Army] on *FREE* shipping on qualifying offers.
|Published (Last):||7 May 2010|
|PDF File Size:||17.44 Mb|
|ePub File Size:||14.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
This permits bridge assembly at the same time repairs are being made on the approach tracks. The same methods of launching are used as for single-story assembly.
This method reduces 5–277 jacking height. Position the supports on panels of the inner and second truss over the chord-bolt holes nearest to the female lugs.
Normally, four pair of tongs and eight soldiers are used to carry a transom. If these are the same, the designer is placed the design sequence until the value obtained in a in a judgmental situation.
It is used to carry panels and transoms. Place plain rollers only every 25 feet 7. Use blocks and tackle to position the inner truss panels. Repeating the design se- particular step 12c matches the value in step 12c of quence under the “TRY 2” column using the bridge the previous design.
Therefore, maximum allowable 16a.
Bailey FM | Pa Ka –
This can result in directed by the field commander. Jacks must be operated on only one end of the bridge at a time. When all three stories are above the decking system, the top chord of the upper story must be braced laterally with transoms and sway braces.
5-2777 Take care that the rocking rollers and base plates are properly positioned when placed on the grillage. Search the history of over billion web pages on the Internet. Determine the final bridge length, truss, and grillage type Solution: These cm help guide drivers to and through the bridge and help to keep traffic moving steadily.
If different, compare this value step 12c to previous “TRY” column. Place flat on top chord of bridge. The counterbalance is normally obtained by adding enough bays of bridge behind the near-snore rocking rollers to act as a counter- weight, keeping the balance point between the plain rollers and the rocking rollers.
Jacking most of the sag out of the bridge makes it possible to place the third- story panels. Tm the weight is carried truss. It used widely and well by Allied armies in Italy describes bridge components, loading and and northwest Europe, If decking of fn trusses is placed in the top story, the trusses do not infringe standard clearance gages.
END POSTS The male and female end posts are the 5–277 as those used in the M2 bridge except that in tripe-truss bridges the male end posts for the middle truss of both class 30 and class 80 bridges above the transom bracket removed. Two types of hydraulic power units are used: In all other bays use plain and button stringers, M2.
Note that in some bridges the rocking-roller reaction is greater than the base-plate reaction.
Attach all bracing frames as for a single-lane bridge. They cannot be strengthened by local Caution tm are all 25 percent greater chord channels. These tongs are used to carry transoms by clamping them over the top flange.
B A I L E Y B R
Only enough room is present to work four jacks at one end of the bridge. Post assembly these holes and tightening hex nuts. Take care that the rocking rollers and base plates are properly positioned when placed on the grillage. Triple-double bridges can be launched using a temporary launching pier.
Submit panels linked by pinned joints. Care must be taken when The measurement of the gap depends on the probably fail if the bridge load were applied completing the design process or the condition of the abutments Figure Roller heights must be fixed so that the tail of the bridge is at least 6 inches Cutoff the top lugs of the end posts flush with the trusses so they do not interfere with the decking.
Looking for PDF of TM 5-277 M1 (or M2?) Bailey type Bridge
Panel bridge equipment is normally used to assemble fixed simple-span, through-type 5-2777 from 30 to feet long. No I never saw that before. This makes it possible to use trucks to tow trailers if necessary. Tie plates, on triple-truss bridges only. Each part of the Bailey bridge is a standard machinemade piece and is interchangeable among spans. If not, use this as your final bridge length and go to step The center grillage must be twice location. In the last bay use three plain stringers, M3.
Jacks fmm be used as an expedient, although the 5-foot 1. The slope of the ramp must not exceed 10 to 1 for loads up to and including 50 tons, and 20 to 1 for loads over 50 tons. Remove construction chess behind the front vertical in the first bay so decking drops into place. The transom rests on the lower chord of the panel and is held in place with a transom clamp.
However, the launching normal seating on the inverted panels.